|
Ingear Limited |
|---|
$60.00
In Stock
Product Code: C01302
Brand: Autoglym
Introducing Autoglym Polar Seal, a specially formulated protective coating designed for effortless application through a pressure washer with Autoglym Polar Blaster Cannon. This innovative solution creates a hydrophobic layer on your vehicle's paintwork, causing water to bead on the surface. The result? A stunning high-gloss finish that not only looks impressive but also drastically reduces drying time.
Polar Seal imparts a hydrophobic layer onto your car's paintwork, creating water beads that make drying your vehicle a breeze. This protective coating not only enhances the visual appeal but also adds a layer of defence against the elements.
Ensure that the bodywork and wheels are cool to the touch and out of direct sunlight before application. We recommend starting with a snow foam like Autoglym Polar Blast to gently loosen dirt, followed by Autoglym Polar Wash for comprehensive cleaning.
Only a small amount of Polar Seal is required. Pour no more than 40ml (four capfuls) into your foam bottle, adding at least 200ml of water. Over-application (more than 40ml) can compromise the finish.
Spray Polar Seal onto the clean, wet vehicle, covering all exterior surfaces except the windscreen. Thoroughly rinse and dry your car to reveal the high-gloss finish with a hydrophobic coating. Drying with a cloth is crucial to prevent water spotting.
Experience the brilliance of Autoglym Polar Seal – a hydrophobic coating that transforms your car care routine, delivering a stunning finish with minimal effort. Achieve a showroom-worthy appearance while protecting your vehicle from the elements. Enjoy your driving experience.
Q: What is Polar Seal?
A: It is a coating designed specifically for use in a pressure washer. It is the coating element (third and final stage) of the three-stage Polar range process. It is preceded by the prewash – Polar Blast and shampoo - Polar Wash.
Q: Is Polar Seal wax safe?
A: Polar Seal is wax safe and we would recommend that if there is wax on the paintwork that Polar Seal is used as a top up. There is no need to remove the wax or other protection before applying Polar Seal.
Q: Is Polar Seal pH Neutral?
A: Polar Seal is pH Neutral and can be used on full exterior of the vehicle, avoiding the windscreen.
Q: Do I use Polar Seal instead of a wax?
A: Polar Seal is a durable hydrophobic coating. However, it does not offer the same long-term protection as Ultra High Definition Wax or Extra Gloss Protection.
Q: Should I agitate the foam once I have applied Polar Seal?
A: No, it is not necessary. The vehicle should be clean before applying Polar Seal, ideally with Polar Blast and Polar Wash. Polar Seal should be sprayed over all exterior surfaces apart from the windscreen and then rinsed off immediately.
Q: What is the recommended Dilution rate for Polar Seal?
A: We would strongly recommend not using more than 40ml Polar Seal and 200ml water. Over use may cause white spotting and significantly compromise the effectiveness of Polar Seal. Using more product will not improve the depth of shine or increase its durability.
Q: Why is it not recommended to use on the windscreen?
A: Polar Seal contains silicones, which in some cases, can create smears once wiper blades are used on the windscreen. We would recommend cleaning your windscreen after you have applied Polar Seal to the rest of your car as part of your car cleaning process.
Q: How long should I leave Polar Seal on my paintwork?
A: It is important that Polar Seal does not dry on to the surface of the vehicle. Once the car has been coated it should be rinsed immediately.
Q: Can Polar Seal be used on my alloys and exterior plastics?
A: Yes, apart from the front windscreen we would recommend Polar Seal can be used on all exterior surfaces.
Q: Is it ok to leave Polar Seal in my foamer bottle?
A: We would recommend that only the product needed for a single application is used. We also recommend that the foamer bottle is rinsed thoroughly after use.
Q: How frequently do I need to apply Polar Seal?
A: There is no benefit to building layers of Polar Seal. We would only recommend reapplication once water beading has ceased. We certainly do not recommend application more than once a month.
